Download Z-2400-A2 Wireless Multiplexer Connections Supplementary Guide - Connecting a 2400-A16/PLC to 2400-A16 Multiplexers. Update!
Note: Requires the XU-USB programming key.
The Z-2400-A2 series of units support the communication of analogue and digital signals via a wireless link. The series consists of three separate wireless nodes for: Input, Output and Repeating, and does not require a computer to monitor the wireless network. Built on the ZigBee® protocol, this allows for multiple Z-2400-A2 wireless links to operate side by side at the same time.
The Output node is the base and acts as the master for the entire link. The Input node acts as a wireless remote station and seeks for the Output Base to transmit the input signals to. The Repeater node is the bridge between the Input and Output wireless nodes, and is only used when the distance between them is too large to communicate directly.
Note: The Z-2400-A2 Series are used for Stand-alone wireless data links. For MicroScan SCADA wireless data links, the Z-2400 Series are used.
|Z-2400-A2IO||One Wireless Output node and One Input node, Paired & supplied as a Kit:|
|Z-2400-A2O: Output Remote Wireless node. 2x 4~20mA Outputs, 4x Digital I/O.|
|Z-2400-A2I: Input Remote Wireless node. 2x Isolated Universal Inputs, 4x Digital I/O.|
|Z-2400-A2R||Repeater node for Wireless Expansion.|
|PSW-10-F||Instrument Quality 24Vdc Power Supply for the Z-2400-A2 Series:
Output Voltage: 24Vdc
Max Current: 1 Amp continuous
Input Power Supply: 100~264Vac
The Z-2400-A2 Series require the XU-USB Programming Key for Software Configuration:
|XU-USB (Rev 1)||
USB Programming Key for programming Z-2400-A2 Series using uP Configure Programming Software (version 22.214.171.124 or later).
|Antenna Options (Used when greater distances are involved):|
|ZA-OD24-5||2.4GHz Indoor Antenna for Z-2400-A2 Series.
Indoor 5.5dBi Omni Directional Rubber Duck Antenna.
|ZB-P-45||Extension Coax for Z-2400 Series Indoor Antenna.
RP-SMA Type with Bulkhead 0.2m.
|2.4GHz Outdoor Antennas for Z-2400-A2 Series.|
|ZA-OD24-2||Outdoor 2.2dBi Omni Directional Whip Antenna complete with 0.5m coax cable with bulkhead.|
|ZA-OD24-8||Outdoor 8dBi Omni Directional Monopole Antenna complete with 3m coax cable.|
|ZA-MD24-12||Outdoor 12dBi Mini Directional Antenna complete with 3m coax cable.|
|ZA-PG24-19||Outdoor 19dBi Directional Parabolic Grid Antenna complete with 6m coax cable.|
|2.4GHz Outdoor Antennas for Z-2400-A2 Series with longer Coax.|
|ZC-OD24-2||Outdoor 2.2dBi Omni Directional Whip Antenna complete with 3m coax cable.|
|ZC-OD24-8||Outdoor 8dBi Omni Directional Monopole Antenna complete with 10m coax cable and 0.5m coax with bulkhead.|
|ZC-MD24-12||Outdoor 12dBi Mini Directional Antenna complete with 10m coax cable and 0.5m coax with bulkhead.|
|ZC-PG24-19||Outdoor 19dBi Directional Parabolic Grid Antenna complete with 10m coax cable and 0.5m coax with bulkhead.|
|Z-2400-A2IO||The Z-2400-A2IO is the kit set of the Input (Z-2400-A2I) and Output (Z-2400-A2O) wireless nodes, supplied as a complete set paired to each other with a unique Mesh ID.|
|Z-2400-A2I||The Z-2400-A2I is a 2 channel analogue input wireless node, when switched on it looks for the output node to sends it’s input values to via the wireless link.
The inputs are individually programmable as follows:
|Z-2400-A2O||The Z-2400-A2O is a 2 channel analogue output wireless node. It acts as the base and controls it’s entire ZigBee wireless network. The analogue output is 4~20mA only at 24Vdc. Like the input node, it comes equipped with the matching 4 digital inputs and 4 digital/relay outputs.|
|Z-2400-A2R||The Z-2400-A2R is quite simply a ZigBee wireless repeater. It is used to boost the signal strength between the other two nodes, input and output, to extend the range. The maximum number of repeater nodes per wireless mesh network is 15.|
Note: ZigBee® is a registered trademark of the ZigBee Alliance, Inc.